Tools
Tools
Start
Congratulations - you have completed Tools.
You scored %%SCORE%% out of %%TOTAL%%.
Your performance has been rated as %%RATING%%
Your answers are highlighted below.
Question 1 |
Which of the following tools has a six-point star-shaped head?
A | Phillips screwdriver |
B | Nut driver |
C | Spade bit |
D | Torx driver |
Question 2 |
Which of the following tools has a hexagon-shaped head and is used to remove a screw with a six-point hex-head shaped?
A | Phillips screwdriver |
B | Nut driver |
C | Spade bit |
D | Torx driver |
Question 3 |
Which tool has a variable open end that is used to remove a nut or a bolt?
A | Allen wrench |
B | Flare-nut wrench |
C | Adjustable wrench |
D | Box-end wrench |
Question 4 |
Which tool is used to loosen or tighten set screws?
A | Allen wrench |
B | Flare-nut wrench |
C | Adjustable wrench |
D | Box-end wrench |
Question 5 |
Which tool has a closed end and is used to loosen a nut or bolt?
A | Tongue and groove pliers |
B | Pipe wrench |
C | Adjustable wrench |
D | Box end wrench |
Question 6 |
Which tool is used to loosen or tighten a mechanical fitting on a refrigeration or air conditioning system?
A | Flare nut wrench |
B | Pipe wrench |
C | Adjustable wrench |
D | Service wrench |
Question 7 |
Which tool is used to loosen or tighten a nut or a bolt from the side?
A | Service wrench |
B | Box end wrench |
C | Socket wrench |
D | Open end wrench |
Question 8 |
Which is the proper tool to use when assembling or disassembling threaded pipe?
A | Pipe adapting kit |
B | Pipe wrench |
C | Crescent wrench |
D | Torque wrench |
Question 9 |
Which is the correct tool to use when manipulating access valves on a refrigeration or air conditioning system?
A | Adjustable wrench |
B | Tongue and groove pliers |
C | Torque wrench |
D | Service valve wrench |
Question 10 |
What are the most common size openings for a service wrench used on light commercial refrigeration and air conditioning systems?
A | 3/16”, ¼”, 5/16”, and 3/8” |
B | ¼”, ½”, ¾”,and 1” |
C | 3/16”, 5/16”, 7/16”, and 9/16” |
D | 5/16”, 3/8”, ½”, and 5/8” |
Question 11 |
Which tool would most likely be used to fit on top of a ½” bolt?
A | Vise grip piers |
B | Socket wrench |
C | Needle nose pliers |
D | Service valve wrench |
Question 12 |
Which tool is used to apply a specific amount of force to a nut or a bolt?
A | Pipe wrench |
B | Adjustable wrench |
C | Torque wrench |
D | Service wrench |
Question 13 |
The tool that is used to ensure that ductwork and other work is level is
A | Plumb bob |
B | Carpenter’s square |
C | Tape measure |
D | Level |
Question 14 |
Which of the following is an L shaped tool used to measure materials and check for uniformity?
A | Plumb bob |
B | Carpenter’s square |
C | Tape measure |
D | Level |
Question 15 |
What type of saw is used to cut wood against the grain?
A | Ripsaw |
B | Crosscut saw |
C | Hacksaw |
D | Keyhole saw |
Question 16 |
What type of saw is used to cut wood with the grain?
A | Ripsaw |
B | Crosscut saw |
C | Hacksaw |
D | Keyhole saw |
Question 17 |
What type of saw is primarily used on metal?
A | Ripsaw |
B | Crosscut saw |
C | Hacksaw |
D | Keyhole saw |
Question 18 |
What type of saw is most commonly used to cut drywall?
A | Ripsaw |
B | Crosscut saw |
C | Hacksaw |
D | Keyhole saw |
Question 19 |
Which file has one row of teeth?
A | Single cut file |
B | Double cut file |
C | Triple cut file |
D | Rasp |
Question 20 |
Which file has two rows of teeth that crisscross each other?
A | Single cut file |
B | Double cut file |
C | Triple cut file |
D | Rasp |
Question 21 |
The three common drive sizes that a drill is available in are?
A | 3/8”, ½”, and ¾” |
B | ¼”, 3/8”, and ¾” |
C | 5/16”, 3/8”, and ¾” |
D | ¼”, 3/8”, and ½” |
Question 22 |
The tool used with a drill to install or remove hex head sheet metal screws is called?
A | Hex head adapter |
B | Screw adapter |
C | Torx adapter |
D | Hex head spade bit |
Question 23 |
What tool is used to recess holes in wood and other material so that screws can be driven flush
A | Spade bit |
B | Countersink |
C | Punch |
D | Reamer bit |
Question 24 |
Which bit is preferred for drilling holes in wood?
A | Masonry bit |
B | Countersink |
C | Spade bit |
D | Keyhole bit |
Question 25 |
What tool has a corkscrew shape and is used to bore holes into wood?
A | Masonry bit |
B | Spade bit |
C | Corkscrew bit |
D | Auger bit |
Question 26 |
What tool is used to bore holes in brick, block, concrete, stone, or mortar?
A | Masonry bit |
B | Countersink |
C | Spade bit |
D | Keyhole bit |
Question 27 |
The proper tool to use when creating an indentation in sheet metal is?
A | Punch |
B | Countersink |
C | Torx driver |
D | Auger bit |
Question 28 |
What tool is used to cut a threaded hole in metal material?
A | Tap |
B | Die |
C | Countersink |
D | Cutting tool |
Question 29 |
Which of the following would be the proper tool for threading gas pipe?
A | Punch |
B | Tap |
C | Die |
D | Reamer |
Question 30 |
What tool is used to remove the burrs from the inside of tubing?
A | Reamer |
B | Die |
C | Tube cutter |
D | Countersink |
Question 31 |
Which hammer would most likely be used to remove a nail from a 2X4 stud?
A | Ball peen hammer |
B | Claw hammer |
C | Masonry hammer |
D | Sledgehammer |
Question 32 |
Which hammer, designed for metal work, has a flat back and a round front?
A | Ball peen hammer |
B | Claw hammer |
C | Masonry hammer |
D | Sledgehammer |
Question 33 |
Which hammer has a large head that is designed for pounding block or concrete?
A | Ball peen hammer |
B | Claw hammer |
C | Masonry hammer |
D | Sledgehammer |
Question 34 |
What care should be taken to prevent corrosion after using hand tools?
A | Hand tools must be stored at 60 F to prevent corrosion and metal fatigue |
B | Hand tools should be wiped down with machine oil |
C | Hand tools should be cleaned with mineral spirits after each use |
D | Hand tools should be wiped down with a saltwater solution |
Once you are finished, click the button below. Any items you have not completed will be marked incorrect.
Get Results
There are 34 questions to complete.
← |
List |
→ |
Return
Shaded items are complete.
1 | 2 | 3 | 4 | 5 |
6 | 7 | 8 | 9 | 10 |
11 | 12 | 13 | 14 | 15 |
16 | 17 | 18 | 19 | 20 |
21 | 22 | 23 | 24 | 25 |
26 | 27 | 28 | 29 | 30 |
31 | 32 | 33 | 34 | End |
Return
You have completed
questions
question
Your score is
Correct
Wrong
Partial-Credit
You have not finished your quiz. If you leave this page, your progress will be lost.
Correct Answer
You Selected
Not Attempted
Final Score on Quiz
Attempted Questions Correct
Attempted Questions Wrong
Questions Not Attempted
Total Questions on Quiz
Question Details
Results
Date
Score
Hint
Time allowed
minutes
seconds
Time used
Answer Choice(s) Selected
Question Text
All done
Need more practice!
Keep trying!
Not bad!
Good work!
Perfect!